Tight-tolerance CNC machining for aerospace, medical and defense.

Prototype to production in titanium, Inconel, stainless and engineering plastics. 5-axis milling, Swiss turning and wire EDM, with CMM inspection and full documentation in the same building.

Upload Your CAD See Capabilities
  • AS9100D
  • ISO 9001:2015
  • ISO 13485
  • ITAR Registered
5-axis machining center cutting a titanium bracket with coolant Work envelope 40 x 26 x 24 in
±0.0002 in Typical held tolerance on critical features, verified on CMM
  • Est. 1987Four decades of precision work
  • 62,000 sq ftClimate-controlled facility
  • 94Machinists, programmers and inspectors
  • 99.2%On-time delivery, trailing 12 months
  • AS9100DAerospace QMS
  • ISO 9001:2015Quality management
  • ISO 13485Medical devices
  • ITAR RegisteredDDTC, DFARS compliant

Capabilities

Every process below runs in-house. Pick one to see envelopes, tolerances and the work we usually do on it.

3, 4 and 5-axis CNC milling

Simultaneous 5-axis machining cuts complex geometry, undercuts and impellers in a single setup, which removes stack-up error and handling time. Pallet pools and robotic loading keep spindles running through nights and weekends.

Axes
3, 4, 5 (simultaneous)
Max envelope
40 x 26 x 24 in
Typical tolerance
±0.0002 in
Surface finish
to 16 Ra
Volume
1 to 50,000 pieces
Automation
Pallet and robot cells

Common parts: structural brackets, manifolds, housings, impellers, fixtures.

Industries we machine for

Each sector has its own paperwork, materials and failure modes. We staff and document for them separately.

  • Aerospace and aviation

    Structural brackets, engine hardware, actuator housings. AS9100D, FAIR per AS9102, full material traceability.

    Titanium, 7075, Inconel

  • Medical and life sciences

    Surgical instruments, implant components, diagnostic housings. ISO 13485 controls, validated processes, lot traceability.

    Ti 6Al-4V ELI, 316L, PEEK

  • Defense and military

    Weapon system hardware, optics housings, communications enclosures. ITAR registered, DFARS compliant specialty metals.

    17-4PH, 6061, armor steel

  • Energy and oil and gas

    Valve bodies, downhole tooling, pump components for sour service and high pressure.

    Duplex, Inconel 718, Monel

  • Semiconductor and electronics

    Vacuum chamber parts, wafer-handling components, thermal plates held to flatness and cleanliness specs.

    Aluminum, copper, 316L

  • Robotics and automation

    Gearbox housings, end effectors, precision joints. Repeat production with blanket orders and scheduled releases.

    6061, 7075, tool steel

Hard metals are the job, not the exception.

Material certs and mill test reports ship with every lot. Hard-to-machine alloys are routine here.

Titanium

  • Grade 2 and Grade 5
  • Ti 6Al-4V ELI
  • Beta alloys

Nickel alloys

  • Inconel 625, 718
  • Hastelloy
  • Waspaloy, Monel

Steel

  • 304, 316L, 17-4PH
  • Tool steels, A2, D2
  • 4140, 4340

Aluminum and copper

  • 6061, 7075, 2024
  • Brass, bronze
  • C101 copper

Plastics

  • PEEK, Ultem
  • Delrin, Nylon
  • PTFE, PEI
CMM probe inspecting a precision machined aluminum part

Quality is a department with its own room.

Inspection sits in a temperature-controlled lab, separate from production. Parts are measured against the model, not against the operator's opinion.

  • First Article Inspection Reports per AS9102
  • Material certs, mill test reports and process certs
  • CMM data sheets with ballooned drawings
  • PPAP, SPC and gauge R&R on request
  • NIST-traceable calibration on every gauge
AS9100D Certificate (PDF) Quality Manual (PDF)

Equipment

The machines that make and measure your parts. Brand, model and envelope, so your engineers can check fit before sending a print.

Full equipment list (PDF)
ProcessMachineQtyEnvelope or capacity
5-axis millingDMG MORI DMU 65 monoBLOCK425.6 x 25.6 x 21.7 in, pallet pool
Vertical millingHaas VF-4SS, Mazak VCN-530C1140 x 20 x 25 in
Horizontal millingMazak HCN-50003Dual pallet, 24 in cube
TurningOkuma LB3000 EX II, Mazak QT-2509Up to 20 in swing, live tool, sub-spindle
SwissCitizen L32, Star SR-208Up to 32 mm bar, 12-axis
EDMMitsubishi MV1200R wire, Sodick sinker5Wire travel 24 x 16 x 12 in
InspectionZeiss CONTURA CMM, Mitutoyo, optical comparator6Accuracy to 1.7 µm, scanning probes
ProgrammingMastercam, SolidWorks, CATIA ingestn/aSTEP, IGES, Parasolid, native files

From drawing to dock, no black boxes.

A buyer should know what happens next at every point. Here is ours.

  1. 1

    Quote

    Upload CAD and prints. Quote returned within 24 to 48 hours for standard requests.

  2. 2

    DFM review

    Engineers flag tight tolerances, thin walls and cost drivers before they cost you.

  3. 3

    First article

    Full inspection report on first parts, approved by you before release.

  4. 4

    Production

    Dedicated cell, SPC monitoring, lights-out runs on repeat programs.

  5. 5

    Delivery

    Certs and data ship with the parts. Scheduled releases against blanket orders.

Recent work

Three representative programs. Customer names withheld under NDA.

Assorted finished precision machined components

Titanium actuator bracket

5-axis, single setup replacing a four-operation process. Cycle time cut 38 percent.

Material
Ti 6Al-4V
Tolerance
±0.0005 in
Volume
2,400 per year

Surgical bone screw family

Swiss turned with in-process vision inspection and lot-level traceability.

Material
Ti 6Al-4V ELI
Tolerance
±0.0002 in
Volume
180,000 per year

Inconel fuel manifold

Deep-hole drilling, wire EDM slots and 100 percent CMM inspection with AS9102 FAIR.

Material
Inconel 718
Tolerance
±0.001 in
Volume
600 per year

A shop run by people who still walk the floor.

We have machined critical components since 1987. Employee-owned since 2016, which is why the person quoting your part and the person cutting it care about the same outcome.

We are not a broker. Every part quoted here is made here, on equipment listed above, by a team that averages 14 years with the company.

  • Employee-owned (ESOP)
  • Made in the USA
  • Veteran-friendly workplace
Clean CNC shop floor with machining centers and Swiss lathes

They flagged a tolerance stack on our first print that would have scrapped half the lot. That call saved us a quarter.

Supply Chain Manager, Tier 1 aerospace supplier

Machinists, programmers and inspectors wanted.

Run 5-axis equipment you will not find at a typical job shop. Mastercam on the programming side, two shifts, paid training and a 401(k) match.

View Open Positions

Send us the print.

Upload STEP, IGES or PDF drawings. Need an NDA first? Tick the box and we will send ours before you share anything sensitive.

Alan Swenson Director of Business Development (612) 555-0142 alan@yourcompany.example
  • Quotes in 24 to 48 hours
  • Files kept confidential, ITAR-aware handling
  • Engineering feedback with every quote
Please enter your name.
Please enter your company.
Please enter a valid email.
Please choose a material.
Drag files here or browse STEP, IGES, SLDPRT, DXF, PDF. Up to 100 MB.